HQY 一个和谐有爱的空间

交换机升级步骤

1、准备一个FAT32的U盘

2、到cisco官网上下载交换机镜像

3、将U盘插到交换机上，登入交换机concole输入dir usbflash0：

找到该镜像，注意镜像不要放在中文目录下

Switch#dir usbflash0:

Directory of usbflash0:/

10 drwx 16384 Jan 20 2019 20:20:46 +00:00 System Volume Information

11 drwx 16384 Jan 20 2019 14:44:38 +00:00 ???ios

12 -rwx 537489817 Jan 20 2019 14:44:38 +00:00 cat3k_caa-universalk9.16.03.07.SPA.bin

13 -rwx 199 Jan 20 2019 13:05:22 +00:00 md5.txt

4、将usb下的镜像copy到flash目录下

Switch#copy usbflash0:cat3k_caa-universalk9.16.03.07.SPA.bin flash:cat3k_caa-universalk9.16.03.07.SPA.bin

5、查看镜像是否copy到flash目录下

Switch#dir flash:

Directory of flash:/

69698 -rw- 2097152 Jan 21 2019 07:20:34 +00:00 nvram_config

69699 -rw- 2097152 Jan 21 2019 07:20:35 +00:00 nvram_config_bkup

69700 -rw- 19167872 Oct 22 2018 05:50:43 +00:00 cat3k_caa-guestshell.16.06.04.SPA.pkg

69701 -rw- 27905983 Oct 22 2018 05:50:41 +00:00 cat3k_caa-rpbase.16.06.04.SPA.pkg

69702 -rw- 331879032 Oct 22 2018 05:50:43 +00:00 cat3k_caa-rpcore.16.06.04.SPA.pkg

69703 -rw- 15676032 Oct 22 2018 05:50:41 +00:00 cat3k_caa-srdriver.16.06.04.SPA.pkg

69704 -rw- 16251516 Oct 22 2018 05:50:41 +00:00 cat3k_caa-webui.16.06.04.SPA.pkg

69705 -rw- 4742 Oct 22 2018 05:51:01 +00:00 packages.conf

69706 drwx 4096 Jan 21 2019 07:16:13 +00:00 .installer

69707 -rw- 148 Jan 21 2019 07:16:38 +00:00 bootloader_evt_handle.log

69708 drwx 4096 Oct 22 2018 05:59:35 +00:00 core

7745 drwx 4096 Oct 22 2018 05:53:49 +00:00 .prst_sync

23233 drwx 4096 Oct 22 2018 05:53:52 +00:00 .rollback_timer

30977 drwx 4096 Oct 22 2018 05:54:01 +00:00 gs_script

38721 drwx 4096 Jan 21 2019 07:16:55 +00:00 dc_profile_dir

69709 -rw- 128103 Jan 21 2019 07:17:16 +00:00 memleak.tcl

69711 -rw- 35 Jan 21 2019 07:25:17 +00:00 pnp-tech-time

69712 -rw- 54030 Jan 21 2019 07:25:20 +00:00 pnp-tech-discovery-summary

69713 -rw- 537489817 Jan 21 2019 07:34:06 +00:00 cat3k_caa-universalk9.16.03.07.SPA.bin

1621966848 bytes total (582938624 bytes free)

6、校验MD5值 ，与之前下载的MD5的txt文件进行比对，只要比对最后四位即可

Switch# verify /md5 flash:cat3k_caa-universalk9.16.03.07.SPA.bin

7、show boot查看当前启动引导镜像

Switch#show boot

Current Boot Variables:

BOOT variable does not exist

Boot Variables on next reload:

BOOT variable = flash:packages.conf

Manual Boot = no

Enable Break = no

Boot Mode = DEVICE

iPXE Timeout = 0

8、更改boot引导选项

Switch(config)#boot system flash:cat3k_caa-universalk9.16.03.07.SPA.bin

然后使用show boot确认

Current Boot Variables:

BOOT variable = flash:cat3k_caa-universalk9.16.03.07.SPA.bin;

Boot Variables on next reload:

BOOT variable = flash:cat3k_caa-universalk9.16.03.07.SPA.bin;

Manual Boot = no

Enable Break = no

Boot Mode = DEVICE

iPXE Timeout = 0

9、保存配置

Switch#wr

10、重启交换机

Switch#reload

推荐本站淘宝优惠价购买喜欢的宝贝:

本文链接：https://hqyman.cn/post/2430.html 非本站原创文章欢迎转载，原创文章需保留本站地址！

休息一下~~